Undercounter DishwasherInstallation InstructionsWhat do I need to have to install the dishwasher?• Tools, parts & materials 1-2• Requirements 3-
continued from page 8Direct wire method:Cut a 3/4’ (1.9cm) hole © in right-hand cabinet side, rear or floor. Optional locations are shown.Wood cabinet
Water lineHELPFUL TIP:Routlr^ the water ttne through the left stde of cabinet opening edit make water connection easier.7.Ù’'Measure overall leng
continued from page 1010.Drain hoseCut a 1-1/2" (3.8cm) diameter hole in cabinet wali or floor on the side of the opening ciosest to the sink.11.
11cWaste disposer, no air gap1. Remove the disposer knockout piug.Do not cut end of dram hose2. Attach drain hose O to disposer inlet © with spring-ty
B.Preparedishwasher^WARNINGTip Over Hazard Do not use dishwasher until completely installed.Do not push down on open door. Doing so can result In seri
Apply Teflon tape or pipe joint compound © to 90“ elbow fitting O and connect fitting to water inlet valve O. Hold bracket ® with pliers Tighten elbow
continued from page 146.Stand dishwasher upright.7.Grasp the dishwasher door frame O. Tiit dishwasher backwards on wheeis ©. Move dishwasher ciose to
11.Remove cardboard from under dishwasherHELPFUL TIP:It Is okay if dlshwastier fits ti^itiy lirto cabinet opening. Do not remove insutation blanket— i
déchargeiHtJiIlLSiHiDishwashElectricalConnectionCheck electrical requirements (see pages 4-6). You need to,✓ have the correct electricai supply and
2.Connect the wires © as follows using twist-on connectors © sized to connect direct wire to 16-gauge dishwasher wire:Form bare, ground wire © into a
O3 3O-^ÉiiYour safety and the safety of others is very important.We have provided many important safety messages in this manual and on your appliance.
continued from page 18Water ConnectionHBPRJL TIP:Compiesshm Atthigs:. Slide nut Oonta copper tubmg O about 1 inch (2.5cnt)., Slide femde # onto the hi
6.Place paper towel under elbow. Turn on water supply and check for leaks.Drain Connection7.Route drain hose to avoid contact with motor, door springs
D.Sec Dishwasm^WARNINGTip Over HazardDo not use dishwasher untii completely instalied.Do not push down on open door. Doing so can resuit in serious in
upen ana cióse rne aoor several iimes. The door should open and close easily. If the door closes too quickly, decrease the spring © tension by moving
To customize your dishwasher:(0co"Joc0)Em^m oIf you want to:Order the color accessory you need.Call (U.S. only*)Change door and access pane! colo
Tools and materials neededAll installationsO ® ®A. pliersB. Phillips screwdriverC. 5/16" and 1/4" nut drivers or hex socketsD. measuring t
(0Cabinet opening0)EoCDtsc^WARNINGVElectrical Shock Hazard Enclose dishwasher completely on the top, sides, and rear. Failure to do so can result in d
✓ cabinet front perpendicular to floor.✓ level floor. (If floor at front of opening is not level with floor at rear of opening, shims may be neede
continued from page 4ElectricalIf is the customer’s responsibility: To contact a qualified electrician.To assure that the electrical installation is a
secure power supply coru lu dishwasher terminal box.✓ power supply cord must plug into a mating three-prong, grounded outlet, located in the cabinet
Cut openings In shaded area of caoinet walls or floor as specified in chart:CotomOPENING FOR: DIAMETER:water line1/2" (1.3 cm)drain line1-1/2&quo
1.A.Disconnect the power supply. Turn water off.2.Put on gloves and safety glassesIf you are replacing a dishwasher;✓ check that the water line Q re
Kommentare zu diesen Handbüchern