Assembly Instructions/Use and Care ManualBÊb ÀKGnmarGLiquid Propane Gas Griliwith Grill@Night™ Night Light Modei No. 415.162180This Grill Is For Outdo
Grill Bottom/Control Panel Assembly and Tank Wire□ Carefully place grill bottom/control panel assembly onto cart, so as not to scratch paint on legs.
End Cap, Side Shelf, Tool Holder and V-bar Assembly□ insert end caps into ends of leg tubes.□ Position side shelf onto tight legs as shown below and
Sidebumer Assembly□ Place sidebutner body onto legs. Secure at front with one wing screw through leg, tool holder, and into body.□ insert tab on sid
Grill Lid, Temperature Gauge and Bezel Assembly□ Attach grill lid to grill bottom with hinge pins and hitch pins.□ Remove wing nut from temperature
Grill@N[ght™ Night Light Handie AssembiyNote: On the underside of the iamp assembiies are “L” for ieft side and “R” for right side. Match to ietter on
SwingAway And Cooking Grate Assembly□ insert lower SwingAway pivot wires into bottom holes in sides of grill lid.□ insert lower SwingAway leg wires
Tank Wire, LP Tank, Grease Clip and Battery I H and ignitor Button Assembly□ Place LP tank into hole in base with tank valve facing toward front of g
USE AND CARE iNever fill the cylinder beyond 80% full. An overfilled spare LP tank is hazardous due to possible gas released from the safety relief va
LP Tank Exchange• Many retailers that sell grills offer you the option of replacing your empty LP tank through an exchange service. Use only those rep
6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP tank valve, resulting in so
FOR YOUR SAFETY1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.2. An LP tank not
For Safe Use Of Your Grill And To Avoid SeriousInjury:• Do not let children operate or play near grill.• Keep grill area clear and free from materials
CAUTIONPutting out grease fires by closing the lid is not possible. Grills are well ventilated for safety reasons.Do not use water on a grease fire. P
Before Your First Cookout• Light burners, check to make sure they are lit, close the lid and warm up grill on HIGH for 15 minutes. Curing of paint and
Cleaning The Burner AssemblyFollow these instructions to clean and/or replace parts of burnerassembly or If you have trouble igniting grill.1. Turn g
storing Your Grit!• Clean cooking grates.• Store in dry location.• When LP tank is connected to grill, store outdoors in well- ventilated space and ou
Cooking ChartCooking times and temperatures may vary according to specific recipes, cooking conditions or barbecue equipment used. Take these factors
TroubleshootingProblemPossible CausePrevention/SolutionBumer(s) will not light using ignitor.• Wire and/or electrode covered with cooking residue.• El
Troubleshooting - Electronic Ignition SystemProblemPossible CauseCheck ProcedurePrevention/SolutionNo sparks appear at• Battery not installed • Check
Get it fixed, at your home or ours!Your HomeFor repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling s
TABLE OF CONTENTSFor Your Safety...2Gril! Service Center...
PARTS LIST - Model No. 415.162180;K6V Qis Description Part# Key Qis Description Part#1 2Leg Assembly... ,,45
PARTS DIAGRAM - Model No. 415.16218044434149A ' 42 44-----> 4619 27i /1 : > A-"23P'--7*' oi*-25 T \/20241210463845504 *5
ASSEMBLY - Model No. 415.162180Cart Assembly Step 1□ Position base on edge with tank hole to left side.□ insert legs into base and attach with carri
Cart Assembly Step 2□ insert wheel/hubcap assemblies into bottom holes on left legs.□ Secure beneath base with hitch pins. See inset below.□ Push i
upper And Lower Front Panel Assembly□ Snap the upper and lower front panels together.□ insert the two pins on lower panel into holes in front of car
upper Panel Wire And Condiment Wire Assembly□ insert panel wire through upper panel and into leg, then bend wire slightly to insert opposite end.□ H
Kommentare zu diesen Handbüchern