Kenmore 1206 Bedienungsanleitung

INSTRUCTIONS MODEL 20/21/23/1206/1300ZIG-ZAG SEWING MACHINE

THREADING UPPER MACHINEPlace thread as iDustrated between discs of the Thread Tension Control.Prevent the spoo! of thread from turning a

PICKINQ yp BOBBIN THREADRaise presser foot lever.Hold needle thread loosely in left hand and rotate hand wheel toward you one complete turn.Br

SETTING STITCH LENGTHTum knob to any desired stitch length position between 0 aofi 5. At No. 5, the longest stitch is obtained. The

ADJUSTING TENSIONSA perfect stitch will have threads locked between the two layers of fabric with no loops on top or bottom.Fig, 1

When stitching is unsatisfactory as in figures 2 and 3, adjust the upper thread tension. Lower thread tension requires adjustment less fre

INSERTING AND REMOVING THE MATERIAFor all kinds of sewing, consult chart page 5.Before placing the matenal on the machine see that:• The presser foot

TURNING A CORNERStop your sewing machine and make sure needle ts in fabric. Raise presser foot. Turn fabnc to de.sired direction. Lo

ZIGZAG CONTROLW NД VTo produce a zigzag stitch, turn the stitch width limiter В upward. A.s the knob is moved up, the stitch becomes wid

BUTTONHOLESStitch length about Stuch Width about 2 Feed doi; control to nsht1. Stitch forward until desired length for buttonhole is obtained. Stop w

The Blind Stitch Knob must be on the “OFF” position for all operations except blind stitching.1- Prepare the hem with a turned and edgestitc

Adjusting for Good Stitching ... .26Placement ..., cBobbin:Oiling Instructions- ' 22,23Inserting & Threading. . .

3. Make second foid as shown.Turn blind stitch knob (black arrow) to the “ON” position. Set stitch width at 0 and siiich length 2-3 (a

DARNINGWITH PRESSER FOOT;1. Turn feed dog control to left.2. Press down outer ring of presser foot pressure regulator, see page 10. With regulator i

L Turn feed dog control to left. Place needle into left hole of button, align holes with slot of presser foot and lower presser foot,2, S

CLEANING AND OILING...Keep the moving parts free from dust aad threads for quiet and efficient operation. Cleaning b

Shuttle AssemblyShuttle Race CoverShuttleShttle RaceIt may be necessary to clean the shuttle area occasionally.L Raise the needle bar to its highest p

WHAT TO DOPROBLEMPROBABLE CAUSECORRECTION1 rregular StitchesIncorrect Size needle.Improper threading.Loose upper thread tension. Pulling fabric.Light

PROBLEMPROBABLE CAUSECORRECTIONSkippingStitchesincorrect size needle.Bent or blunt needle, incorrect setting of needle. Tight upper thread tension. Li

ADJUSTING YOUR SEWING MACHINE FOR GOOD STITCHESWhen your sewmg machine does not sew a properly locked stitch, check the following:1. Insert a new nee

PARTS LISTAil parts listed here may be ordered through your nearest Sears or Simpssns-Sears retail store, catalog sales office or mail order house.Whe

SEWING MACHINENow that you have purchased your Sewing Machine, should a need ever exist for repair parts or service, simply contact any Sears Service

FRONT VIEWi.4.•J! •6.7...(R)- -,5'"^ -, .' /'1-4 a•>;v-if"ryy/Bobbin Winder Spindle Bobbin Winder Latcb Stitch Widt

BACK VIEW2L Presser Foot Pressure Regulator22. Face Plate23. Presser Foot Lever24. Thread Cutter25. Hand Wheel26. Clutch Release 2?. Thread Spool

INSTALLING MACHINE HEAD IN PORTABLE AND CABINETLoosen the two hinge screws under holes in the rear edge of the machine bed (1).Raise hinge

NEEDLE AND THREAD TABLETHREAD SIZENEEDLESIZEfabricCotton 60—100 Synthetic Silk A11Sheer cottons, silks, and synthetics Fine LacesCotton 60—80 Merceriz

REMOVING BOBBIN CASE FROM SHUHLE/Take up lever at Its highest position.Pulioutlatch.C&¡Pull bobbin / case straight out.

WINDING THE BOBBINoPlace thread on spool post. Draw thread as shown.Release clutch by turning clutch knob toward you. Start machine.0Wind

INSERTING BOBBIN INTO BOBBIN CASE...CASE INTO SHUTTLE<1- Guide bobbin onto center pm of bobbin case. Pull thread through slot.Pull thread under ten