Use & Care Guide Manual de Uso y CuidadoEnglish / EspañolModel / Modelo No. 625.383500Kenmore Water Sowith High FAblandador dcon vélvu o flujoN5V
nstallatìonLEAK TESTTo check for leaks, complete the following steps:CAUTION: To avoid water or air pressure damage to softener inner parts, and to fl
nstallationINSTALL GROUNDING CLAMPThe house cold water pipe (iron or copper) is often used to ground all electrical outlets in the home. To maintain t
Programming the SoftenerSET SALT LEVEL button Display UP button SELECT buttonFigure 15PROGRAM THE SOFTENERWhen the transformer is plugged into the ele
Programming the SoftenerSET RECHARGE (REGENERATION) START TIMEIf you completed the previous step, the words “RECHARGE TIME" should show in the d
Sanitizing the SoftenerSANITIZE THE WATER SOFTENER1. Open salt lid, remove the brinewell cover and pour about 3 oz. (6 tablespoons) of household bleac
Controller FeaturesEXTRA RECHARGESometimes, a manually initiated recharge (regeneration) may be desired, or needed. Two examples are:• You have used
Controller FeaturesOPTIONAL SETTINGS:• SALT EFFICIENCY• CLEAN FEATURE• CLEAN FEATURE MINUTES• MAXIMUM DAYS BETWEEN REGENERATIONS• 97% FEATURE•
Controller Features4. Press SELECT again to display the “Recharge Days” screen.6. Press SELECT again to display the “12 or 24 hr” screen.Default Dis
Controller FeaturesTANK LIGHTTo light the the inside of the salt storage tank, press the TANK LIGHT button on the faceplate. Press t
Care of Your Water SoftenerSALT BRIDGESometimes, a hard crust or salt “bridge” forms in the brine tank. It is usually caused by high humidity or the w
WarrantyWARRANTY ON KENMORE WATER SOFTENERONE YEAR LIMITED WARRANTY ON WATER SOFTENERWhen installed, operated and maintained according to all instruct
Service InformationTROUBLESHOOTINGIf your water softener does not work properly, make the following easy checks. Often, you will find what is wrong yo
Service InformationMANUALLY INITIATED ELECTRONIC DIAGNOSTICS1. To enter diagnostics, press the SELECT button and hold for three seconds. The display w
Service InformationMANUAL ADVANCE REGENERATION CHECKThis check verifies proper operation of the valve motor, brine tank fill, brine draw, regeneration
Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com23
Water Softener Exploded ViewQuestions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com24
Softener Parts ListKeyNo.Part No. Description17275907Transformer, 24V, lOVA27325168Top Cover3 7325223Salt Lid (order decal below) 7325231Instruction D
Valve Assembly Exploded ViewQuestions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com26
Valve Parts ListKeyNo.Part No. Description50 7224087Screw, #8-32 X 1” (2 req.)51 7286039Motor (incl. 2 ea. of Key No. 50)520900857Screw, #6-20 X 3/8”
Get it fixed, at your home or ours!Your HomeFor expert troubleshooting and home solutions advice:@managemylifewww.managemylife.comFor repair - in your
Table of ContentsWarranty...2Safety Guides...
Specifications & DimensionsModel No. 625.383500Model Code350Rated Softening Capacity (Grains @ Salt Dose)12,600 @ 2.5 lbs. 26,900 @ 7.9 lbs.
Packing ListThe parts required to assemble and install the water softener ore included with the unit. Thoroughly check the water softener for possible
Plan Your InstallationTYPICAL INSTALLATIONWHERE TO INSTALL THE WATER SOFTENERReview the following points before you choose a placeto put your softener
Plan Your InstallationCHECK YOUR WATER PRESSURE BEFORE INSTALLINGFor your water softener to work properly, incoming water pressure in your house pipes
nstallatìonINSTALL SINGLE BYPASS VALVE (coni.)Before installing the bypass valve and/or installation adaptors, make sure that the turbine
nstallationCONNECT THE VALVE DRAIN HOSETake a length of 3/8” inside diameter drain tubing (supplied) and attach one end to the drain fitting (see Fig.
Kommentare zu diesen Handbüchern